PS5 Digital Edition: GameVinyl Console Skins Application Guide

Thank you for purchasing one of our GameVinyl Console Skins for PlayStation 5 Digital Edition! Below is our application guide to help you get started.

Items that can make this process easier:

  • A steady set of hands
  • Scissors
  • Hairdryer or heat gun (optional)
  • Credit card (optional)

Step 1: Clean the device

This is an often overlooked but absolutely essential step. If you don't clean it, any debris that is left on it will show through the skin! Take some glass cleaner and spray it on the device, then use a microfiber towel or other clean towel to wipe off. Stay away from paper towels, as they can leave lint.

Step 2: See what you're working with

Unroll and lay out the vinyl material on a flat surface. We recommend you use the largest table you can find to perform the installation. Below is what you'll see when it's laid out.

Make note of the pink cut lines. You won't see these on the physical printout, but that's where the cuts are in the print. This is where the skin will peel off of the backing piece of vinyl material.

Let's start off by installing the main two pieces, beginning with the front plate.

Step 3: Front Plate

This is the easiest of the plates to do. If you have a second set of hands, you can peel the entire piece off, and align a corner to begin. Slowly work your way down until your alignment is spot-on. Your helper can hold the other side of the piece so it does not stick to the console. If you mess up, don't worry. The material is meant to be stuck and unstuck if necessary without causing damage or reducing the adhesiveness. Simply unstick, and try again. To help prevent or remove air bubbles, take a hair dryer or heat gun and apply heat to the skin after application, and use a credit card or other hard plastic tool to iron out any air bubbles that may have formed. 

If it's just you: Before peeling off, use a pair of scissors to (carefully) cut this entire piece off of the main roll of vinyl. By doing this, you will be able to peel off just the top of the sticker - enough to get a corner onto the plate, while still having everything under it still on the backing material. This will make it easier because you will not have to worry about the rest of the piece sticking onto the console before it's properly aligned. It will also help prevent air bubbles. For reference, see this video tutorial below for this method:

 

Step 4: Rear Plate

Repeat the process as the front side. If you had a disc version PS5, this would be a bit more complex - but you don't, so it's a lot easier!

Step 5: Middle Skin

Place your PS5 in the standing position. Start peeling the skin from the backing paper. Start from the bottom (near the buttons), and as you peel off, check to see that the 3 cutouts, circled below in red around the two inputs and the one power button, are fully removed as you peel it off. If not, lay the skin back down on the backing paper and manually remove these cutouts. They will already be halfway cut, so you just need to peel them up manually. A razor blade can help. Once you are sure those are fully peeled off, proceed and peel off the entire middle skin.

Use the power button to begin aligning this piece. Start there, and work your way up. If you correctly positioned the skin with the two buttons, the rest should be easy. Just make sure to keep it center-aligned as you work your way up. If you mess up, simply remove it and try again. You can do this as many times as you need to, until you get it perfect.

Step 6: The Top, Bottom and Port Panel

The remaining 3 pieces are rather simple. Just peel and align! Use the port cutouts as an alignment guide on both the bottom section and the port panel section. So instead of starting at a corner of the console, start by aligning one of the ports.

Common Troubleshooting Questions

Q: I see air bubbles in the skin after application. What can I do? 

A: This is where a heat gun or hair dryer will come in handy. Apply heat to the console skin for 30 seconds by switching on and aiming the hair dryer or heat gun towards it. Use a credit card or squeegee to iron out any bubbles by sweeping them toward the sides of the skin. 

Thank you for reading our PS5 GameVinyl Console Skin application guide. If you have any questions or need more help, email us at support@vgfgamers.com.